Renishaw PH10M PLUS Motorized Probe Head, PHC10-3 PLUS Probe Head Controller (which has now replaced the PHC10-2) PAA1 Autojoint & TP20 Modular Touch Probe System with 3 Probe Modules New with 2 Year Warranty.
Renishaw List Price $33,045.00
About PH10 Models
The range comprises three PH10 models, each of which can carry a range of probes and extensions and can be orientated in 720 repeatable positions, giving access to the most difficult-to-reach workpiece features.
All three variants of the new PH10 heads are now supplied with a revised repeatability specification, down from 0.5 µm (2?) to just 0.4 µm (2?) (specified at a distance of 62 mm), giving users improved positioning at the stylus tip. The new specification heads are physically differentiated by a new ‘aqua blast’ finish which gives a modern, matt black appearance.
The PH10M can carry long extension bars and complex probes such as SP25M or TP7M. The highly repeatable autojoint allows rapid probe or extension bar changing without the need for re-qualification.
| Length |
117 mm |
| Width |
62 mm |
| Weight |
645 g |
| Probe mounting |
Autojoint (multiwire) |
| Head mounting |
PH10M shank to suit CMM |
| Suitable controller |
PHC10-3 PLUS |
| Repeatability of position |
0.4 µm (0.00002 in) specified at a distance of 62 mm |
| Total no. of positions |
720 |
| Max recommended drive torque |
0.45 Nm |
| Maximum extension bar |
300 mm (11.8 in) using PAA3 extension |
PHC10-3 head controller receives instructions from the CMM control. The PHC10-3 controls all head functions and reports system status to the CMM:
- Drives PH10 (PH10T, PH10M or PH10MQ) to position - sent either from the HCU1 or CMM.
- Checks and reports position
- Flags up errors, e.g. failure to reach position, obstruction before or after locking etc.
The PHC10-3 does not process any of the probe sensor signals. These are railed clean through the heads axes and controller to the probe interface.
PHC10-3 PLUS specification
| Length |
180 mm |
| Width |
440 mm |
| Height |
44 mm |
| Weight |
1.5 Kg |
| Data transmission |
RS232 or USB |
Current Consumption
(at 240V) |
less than 1 A |
PSU electrical ratings
|
Supply voltage: 100-240 V ± 10%
Frequency range: 50/60 Hz
Power consumption: 49 W max.
Transient voltages: Installation category II |
| Input connectors |
15 way 'D' |
| Power supply |
24 V DC 49 W provided by the Emerson PSU (DP4024N3M) power adaptor |
| Probe output connectors |
7-pin DIN or 9-way 'D' type |
|
Maximum cable length
RS232
USB
|
50 m
5 m (extendible in lengths of 5 m by use of a hub, to a maximum length of 30 m)
|
| Hand held control unit |
HCU1 only |
About TP20
The TP20 is a compact 5-way, or 6-way, kinematic touch-trigger probe system. The two-piece design, comprising probe body and detachable stylus module(s), connected using a highly repeatable magnetic kinematic coupling. This provides the facility to change stylus configurations either manually or automatically without the need for requalification of the stylus tips, thereby giving significant time savings in inspection routines.
Modules offering a range of trigger forces allow the probe performance to be best matched to the measurement task. A set of probe extensions is also available, as is a 6-way module. The stylus mounting thread accepts styli from the Renishaw M2 range.
The TP20 system is easily retrofitted and is compatible with existing touch trigger probe interfaces, extensions and adaptors.
System components
The system components are:
- TP20 probe body
- TP20 probe module - seven variants allow optimisation to suit application
- MCR20 module changing rack - automatic operation
- MSR1 module storage rack - manual operation
- Suitable for interfacing with Renishaw's PI4-2, PI7-2 or PI200
